When setting up a shower in a country house, different foundations are used. The bases are standard structures of a smaller version without the elements that provide the strength of large structures.
The type of foundation depends on the volume of the load. It is necessary to take into account the lining material and the weight of the tank filled with water. The foundation of a summer cabin can be columnar, strip, or slab.
Anyone can build a foundation with their own hands. It is important for a summer resident to have a little knowledge of the construction process and basic information about earthworks. Based on the chosen type of foundation, the order of work on the site differs.
Required tool:
- Concrete mixer (can be replaced with a regular container);
- Shovel;
- Level;
- Hacksaw;
- Rope;
- Drill;
- Master OK.
Prepare yourself for pouring the foundation. The main thing is to maintain certain proportions. It is advisable to measure the components in buckets. In the absence of a concrete mixer, it is most convenient to mix the solution in a basin with a hoe. 
Sand (about two buckets) and a bucket of cement are poured into the container. The components need to be mixed. Add water little by little, the volume of liquid does not exceed two buckets. The mixture should become homogeneous. Crushed stone completes the batch. The dry component is added in small portions.
Work on equipping the foundation is carried out with the following materials:
- Metal pipes;
- Beam;
- Fasteners;
- Formwork boards.
When choosing the best location for your shower, there are a few things to consider. The first is the ability to supply clean water and remove dirty water. Locating the shower close to the well is a good option; during installation you won’t have to pull the hose or pipe far. 
The water must be drained into a drain or septic tank. If this is not done, the flowing water will fall into the aquifer, from which the well is fed.
Most summer residents prefer that the water in the tank is heated by the sun. It is necessary to install the shower foundation on the sunny side, well protected from the wind. It is undesirable to locate the shower stall close to the boundaries of the summer cottage.
Water drainage
To ensure that water flows freely from the site, moistening the vegetation planted near the cabin, the summer shower is made on an elevated surface. It is chosen based on the terrain features of the site, or it is done with your own hands by adding soil. 
An important stage in building a foundation is to create a drainage system for used water. If the drainage is not organized correctly, rot may form in the shower stall due to high humidity. It will not look aesthetically pleasing, and an unpleasant odor will appear in the room.
The easiest option for drainage equipment is drainage. It should be done in the shade at a short distance from the booth.
The drainage will require a hole that can accommodate two ten-liter buckets. A pipe from the shower is installed into the hole; water will flow through it. A standard sewer pipe is suitable for transportation. Then the hole will need to be completely filled with crushed stone. Water will seep through it, being absorbed by the soil.
To mask the drainage, or sow the area with lawn grass. It will be necessary to fill the hole with crushed stone not completely, leaving twenty centimeters of agrofibre and soil.
Ribbon view
This foundation is in little demand. When laying, it is necessary to observe the recommended depth of the monolith tape - it should not exceed thirty centimeters. This value is ideal to ensure maximum strength of the base. 
The disadvantage of a belt-type base is its labor intensity and high cost.
The first stage of work includes a detailed breakdown of the base with precise fixation of turning points using reinforcement or pillars. The quality of the future structure directly depends on compliance with the form. Carefully measure each side by checking the diagonals of the rectangle.
A rope is stretched between the marker posts. After this, they begin digging a trench, along the edges of which formwork will then be installed. The prepared trench is filled with concrete. After the mixture has hardened, the horizontalness of the surface is measured with a hydraulic level.
Piles
The most popular type of equipment for a shower house is a pile foundation. It's easy to do it yourself. You need to mark the corners of the rectangle. You need to drill deep holes in the corners (about one and a half meters). Pipes made of asbestos cement or metal are inserted into the recesses so that they rise above the ground. 
The preferred pipe diameter is ten centimeters. An anchor pin equipped with a screw thread is mounted on top of each pile.
Pipe piping is made from rolled metal or wooden beams. Holes are made in advance for fastening to piles. After this, the harness is placed in the desired position and secured with a washer and nut. Next, work is carried out on installing the frame, installing the cabin roof and internal lining.
When building this foundation, you will need to dig four square holes for the pillars. The depth of the pits should be at least 50 and the size should be 20*20 centimeters. Sand should be poured into the recesses so that it covers the bottom of the hole. Then you should put a waterproofing layer and treat the walls with roofing felt. 
To concrete the upper parts of the pillars, which will be above ground level, formwork is installed.
Cement mortar is poured into the pits; small crushed stone or crushed brick can be used. Before pouring concrete, it is recommended to strengthen the reliability of the foundation pillars using reinforcement bars by inserting them into the recesses.
Requires strapping. You need to place a threaded pin in the center of the post so that it is sunk two-thirds into the solution. After this, they make the strapping and begin installing the cabin structure.
Detailed construction instructions are given in the video:
By observing the recommended parameters and technical standards, a strong, durable structure is obtained. A shower with a foundation built by yourself will be an excellent solution for a summer cottage and a budget-friendly way to create a place for hygiene procedures in a summer cottage.
An outdoor shower is a necessary building at every dacha, especially if there is no pond or other places in the immediate vicinity where you can rinse off. The shower is a good way to freshen up after a hot day, or to wash away dust and dirt after gardening work. You can try to build such a building with your own hands. We provide tips and instructions on how to do this with a minimum of money and effort in this article.
A little about the benefits
The main advantages of a summer shower are:
- efficiency - to heat water for bathing in the simplest design, you only need the sun; you can wash without costly and time-consuming communications;
- convenience;
- accessibility for making with your own hands from scrap materials;
- the possibility of taking water procedures at any time of the year with good thermal insulation;
- some models allow you to shower anywhere;
- minimal maintenance costs.
Did you know? The prototype of modern showers are primitive baths that were built by the ancient Indians, Egyptians and Mesopotamians. They were partitions behind which people doused themselves with water, or ordered servants to do so. But the first showers, in which water flowed upward, were invented by the ancient Greeks. Proof of this is the images found on Athenian vases dating back to the 4th century. BC e.
Possible options
There are many options for building a summer shower. There are very simple and easy structures that take several hours to equip; There are capital ones that will serve for many years. After familiarizing yourself with the various options, you can use some ideas or take ready-made instructions as a basis.
Simple ways to arrange a summer shower
The simplest option for bathing in the country is a portable shower, which is sold in stores. It is a 20 liter water tank with a hose. The tank is hung on a tree or other vertical surface in a place that is well lit by the sun and filled with water. Once the water has warmed up, the hanging shower can be used. There is enough water in it to take water procedures for 10 minutes. 
A tank equipped with a tap can also be used as a hanging container. A hose ending with a shower head is attached to it. The tank will need to be attached in a sunny place at a height slightly higher than human height (however, so that a person can reach the faucet with his hand).
Another simple way to arrange a bathing area is a lightweight shower structure that can be attached to the wall of any building. In this case, the wall will need to be covered with a special material that protects it from contact with water, for example, tiles or film. Such a shower can be either open or closed using a screen.
The stand is convenient because it can be installed anywhere where the water supply reaches.
The common disadvantages of the first three options is openness to prying eyes and winds. Usually, people swim under such a shower only in a swimsuit and in very warm weather. 
An option that is gaining more and more popularity due to its simplicity, compactness and affordability. To set it up you will need two corrugated hoses, two rubber pedals with valves (a rubber mat with a built-in pump), a container of water, and a shower head. The principle is that a person stomps on pedals or a mat with his feet, thereby pumping water from a container that flows into the hose.
A treadmill shower can be purchased ready-made in a store or made with your own hands using a car pump. 
This design involves driving four wooden (or other material) posts into the ground. You need to place a plastic tank on them into which water will be poured. It will also serve as the roof of the structure. A hose is attached to the tap in the tank, onto which a watering can is placed. The racks are covered with moisture-resistant material. The floor is a rubber mat.
A frame shower can be made from various materials. The simplest option can be built in a couple of hours. It can be made temporary and dismountable. That is, you can put it away indoors for the winter and take it out at the beginning of the new summer season. 
Important! When building a summer shower, you should choose black water containers. This way the water will warm up faster, since this color attracts the sun's rays best. In addition, the water temperature will be much higher.
The most complex and serious version of a summer shower without a foundation. This is a ready-made stationary shower stall with a door, equipped with a water tank and a tray. It is made of wood, polycarbonate, corrugated sheets, plastic or tarpaulin. The water tank can be heated either by the sun or by electricity. The cabin can be equipped with a dressing room-vestibule, in which things and shoes are left. It can also be made completely closed or semi-closed.
In addition to the design options described above, there are many design ideas for a summer shower. Using them, you can create a washing corner to suit every taste and budget.
Capital buildings
In this subsection we have selected an overview of models that are made with pouring the foundation. Their walls are made of different materials:
- wood,
- gland,
- slate,
- plastic,
- polycarbonate,
- plexiglass,
- plywood,
- profiled sheets,
- bricks
Basic principles for installing a country shower
To build a high-quality, durable shower, several conditions must be met:
- choose a suitable location;
- decide on the materials from which the tank, base and foundation will be made;
- think about how the drain will be arranged;
- estimate whether the shower will consist of one room, or whether the installation of a vestibule, toilet, etc. will be required;
- depending on how you plan to use the shower - throughout the year, or only in the summer - provide the possibility of heating the water.
Selecting a location
The first thing that needs to be done is to choose a good place for construction. The following factors influence his choice:
- the water will heat up naturally or automatically;
- it will be poured into the tank manually or automatically;
- what materials are planned to be used for the foundation and walls;
- dimensions of the building.
The shower will need to be installed close to the water supply, so as not to carry water far, or so that the hose can easily reach it. The choice of location will also be determined by what materials the building is made of, how much space it will take up, whether it needs to be hidden from human eyes, or whether it can fit harmoniously and beautifully into the complex of the entire summer cottage. If you plan to install a tank with a heating element, then the shower room will need to be located in close proximity to the power supply.
Tank selection
The tank can be plastic, metal, polymer. A similar container can be purchased at a specialty store. You can also use any suitable thing - for example, an iron barrel, etc. - that can be found on the farm. Its volumes must be calculated based on the requirement of at least 40 liters per person. The maximum capacity volume is 200-250 l. Dimensions are selected according to the area of the building. 
As for the shape, a flat tank is considered the most rational - it is easier to install on any structure, and the water is heated evenly. Round and square tanks are also common today.
If you prefer metal tanks, you should note that they should be treated with anti-corrosion agents and paint (except stainless steel). The service life of metal tanks with proper treatment is about 10 years. Stores usually sell containers made of galvanized, stainless, and carbon steel. The best and most expensive option is a stainless steel tank. They are usually rectangular containers with a capacity of 40 to 200 liters.
Plastic containers can last 30-50 years. Their advantages are lightness, ease of installation, efficient water heating, low maintenance requirements and low cost. Without heating, plastic containers hold 100-200 liters. They are equipped with lids at the top into which water is poured. Unheated tanks can be round or square. 
You can adapt a plastic or metal barrel to a homemade tank by cutting a threaded outlet at the bottom. In the future, you can insert a pipe or pump there.
Drain options
So, you have decided on the place of construction, the materials from which it will be made, and the type of tank. Now is the time to think about where the used water will go.
Important! If the withdrawal is not organized correctly,or is not organized at all, then after some time after use, an unpleasant odor, rot, or mold may appear in the shower stall.
Base and foundation
The foundation for construction can be of different types. The main ones:
The choice of foundation will depend on the type of materials from which the walls are made, as well as the volume of the water tank and the technical characteristics of the soil.
Availability of a toilet
A country shower can be combined under one roof with a toilet. This will save space and materials. Only one strip foundation will need to be poured, as well as the installation of only one drain. In addition, this will allow you not to litter the site with small buildings, because most dachas cannot boast of vast territories. And this is a significant time saving - building one compact structure will be much faster than two.
Possibility of heating water
If you plan to use the shower not only on warm sunny days, you need to consider the possibility of automatically heating the water.
A heating element with a power of 1.25-2 kW can be inserted into the heated tank. In this design, the water will heat up for about three hours. 
Heating element for heating water
Important! If you plan to install just such a tank, you should know that you will need to constantly monitor the presence of water in it - the exposed heating element will burn out when turned on. Therefore, such a container must have a constant supply of water by pump or water supply.
It is also advisable to equip it with a sensor that will show the water level. 
How to build a budget outdoor shower
A budget shower can be built from metal pipes and wooden planks. You will need the following materials:
- metal pipes (40 x 40 x 3000 mm) - six pieces;
- pine boards (20 x 95 x 3000 mm) - 21 pieces;
- plastic tank with a volume of 250 l;
- screws;
- sand;
- crushed stone;
- wood oil;
- enamel for metal pipes;
- geotextiles.
Tools you will need:
- Circular Saw;
- magnetic corner for welding;
- Miter saw;
- screwdriver
To reduce the cost of construction, instead of wooden walls, you can use, for example, tarpaulin or other material. However, in this case the construction will be very short-lived. Capital construction
If you are planning a long-term, high-quality construction of a shower that can be used in all seasons, we suggest you consider the following option: on a pile foundation and with a drain in the form of a septic tank. Recommended dimensions for a comfortable shower with changing room: height - 2-2.5 m, width - 1.40 m, length - 1.90 m. For accurate calculations of materials and dimensions, a drawing will be required.
Laying the foundation
The pile foundation can be made from metal pipes with a diameter of 100 mm and a length of 2 m each. For the foundation, draw a rectangle corresponding to the dimensions of the shower body. In the corners you need to drill four holes 1.5 m deep for the piles with a garden or ice drill, or dig them out with a shovel. To extend the life of metal pipes, they are treated with machine oil before being placed in the ground. 
Laying a pile foundation
After digging in the pipes, at least 30 cm should remain above ground level. The pipes must be filled with concrete.
After the concrete has completely hardened, you will need to install the timber and strapping. The frame is held together with long bolts.
Digging a septic tank
For the simplest version of a septic tank, a hole is dug in the immediate vicinity of the shower room, consistent with the dimensions of the receiving chamber, about 2 m deep. The walls are lined with brick or cinder block. Under the receiving chamber, you can use a barrel or other containers that can be closed with a lid. A gutter is brought to the receiving chamber and connected to the drain pipe. The drainage gutter is lined with waterproofing material. 
Frame installation
The shower frame is a welded structure made of metal pipes with a cross-section of 40 x 40 or 50 x 50 mm. This design will allow you to withstand a 200-liter tank of water. The booth itself can be made of wood, siding, corrugated sheets, or lining. You should consider the presence of ventilation windows in the walls, closer to the ceiling.
If there is no welding, then the structure is made of wooden beams 60 x 80 mm. In this case, the booth will also be wooden. Such a shower will be cheaper. The wood must be impregnated with special water-repellent agents.
After installing the vertical supports, the top trim is made. The side frames are secured with spacers. 
The floor is made of wood. In this case, it will be warm and you can stand on it without shoes. The boards in the floor are made with a gap so that water flows freely.
The door is installed last.
The plastic tank is placed on the roof and secured with straps. The desired water supply scheme is selected.
Shower arrangement
A major shower will require electrical lighting wiring. In this case, it is necessary to adhere to safety rules and insulate the wiring to avoid contact with water. 
All interior decoration must be made of moisture-resistant materials. For a shower that is planned to be used throughout the year, insulation made of foam plastic or other materials will be required.
You should consider the location of shelves for detergents, hooks for clothes and towels, and an internal lock for doors.
Another option for the capital construction of a warm country shower - on a concrete slab with a frame made of wooden boards and OSB sheets - can be seen in the video https://www.youtube.com/watch?v=vwhv_668wwo.
Did you know? The remains of an ancient shower complex, presumably dating back to the beginning of the 2nd century. BC e., were found by archaeologists in the territory of modern Turkey. It consisted of seven installations, into which water came from the main system, was supplied from above, flowed from installation to installation, and then flowed into the drainage system.
An outdoor shower is a necessary outbuilding for summer residents who prefer to use their summer cottage both for the purpose of relaxation and for the purpose of growing fruits and vegetables. It’s easy to make an outdoor shower cabin with your own hands, without having any special skills. However, even for a simple structure, certain conditions will need to be met: choosing the most suitable location with prolonged exposure to sunlight, ensuring unhindered drainage of used water. For more complex capital structures, you will need to carry out design and purchase the necessary tools and materials.
Video: how to make a summer shower at the dacha with your own hands
You can build a shower in your country house with your own hands by following simple instructions. First of all, it is necessary to take into account how the country holiday from the bustle of the city will be spent. A long summer vacation will require the installation of a global permanent structure. For a short stay, a simpler design would be the best option for a good rest in the garden or in the garden.
The main purpose of building a summer shower with your own hands is to provide comfortable water treatments, which are highly desirable in the hot season. Therefore, a very rational approach should be taken to developing design parameters.
Planning a shower in the country
When installing a summer shower with your own hands, you should decide on such important nuances as the organization of drainage, the method of supplying water to the tank and the method of heating it.
- location of the water supply;
- presence of elevation;
- distance from a residential building;
- airflow.
Normal water supply will be possible if the installation of the connecting pipeline is correctly taken into account. The rapid outflow of waste water is ensured by a small slope angle. Therefore, it is best to build a shower at the dacha with your own hands on a hill.
Video: Review of a summer shower cabin in the country
The building is not always placed close to a residential building, but a very large distance from it is not recommended. You should also give preference to the area that is most protected from drafts.
You can independently develop many projects that will make it easy to build a country shower with your own hands. A visual drawing will more clearly outline and determine the choice of the most successful layout for the future structure.
Drawing of a summer shower in the country
Dimensions of a country shower
A shower in a country house should not be a narrow cubicle with a water barrel on top. When calculating the size of the building, you should take into account your own dimensions, as well as all those who will regularly use the shower. There should be a comfortable space inside that allows you to stand freely, turn around and bend over easily.
When building a country shower with your own hands, the standard dimensions are 190x140 cm. With these calculations, the dimensions of the shower stall itself are 100x100 cm, and the changing rooms are 90x40. The height of the structure can vary from 2 to 3 m.
When marking the installation location of the future shower, you need to pay attention to the thickness of the material used. As a rule, for this type of construction, a board is used, the standard size of which is 10 cm. Thus, assuming that the layout dimensions are 190x140 cm, a rectangle of 200x150 cm should be marked on the soil.
Installing the foundation of a summer shower
Building a shower in the garden with your own hands requires the presence of a foundation, the thickness of which is directly dependent on the material used. If the soil is heaving, a monolithic foundation 40 cm high is recommended. Before installing it, it is necessary to create a sand cushion. For other types of soil, preference should be given to the pile technology for installing the foundation.
How to lay the foundation for a summer shower in the country. To lay a pile foundation you need:
- Make holes 1-1.5 m deep in the soil or drive piles into the ground.
- Install asbestos-cement or metal pipes with a diameter of 90-100 mm, leaving 20-30 cm protruding above ground level.
- Make a recess at an angle for the drain pipe.
- Insert waste pipe.
- Fill the piles with concrete, having previously prepared the concrete mixture according to the instructions.
- Level the surface.
- After drying, the foundation should be covered with PVC film or two-layer roofing felt.
Arranging a garden shower drain
How to organize a drain in the shower at the dacha. The drainage system must be installed taking into account the selected technology. The main place is occupied by the laying of a pipeline, which is connected to the general sewer system.
If there is no sewer network or drain nearby, you should dig a hole that matches the size of the tank. On average, the size of the drainage pit is 2-3 m. In addition, it is necessary to think about drainage ventilation.
Installation of a garden shower frame
An important step in the construction of a country shower with your own hands is the installation of the frame of the future building. Metal or wooden beams are used for the frame. Installation of the frame should be carried out in stages. To do this you need:
Construction of the frame for a country shower. - Place beams in the corners and concrete them.
- After the concrete has dried, carry out the lower and upper trim.
- Secure the foundations of the walls to each other using rigid miters.
- Make internal dressings that serve as lags for the future floor.
Arrangement of the floor of a country shower
When starting to arrange the floor, you should take into account such requirements as a high degree of hygiene of the surface, ease of maintenance and the degree of slip. The first stage of floor design is the formation of a threshold that will separate the dressing room and the washing compartment, and also prevent water from leaking. Next, you can install a boardwalk or install a special tray designed for a shower.
When finishing with beams, there should be no gaps that contribute to the occurrence of drafts. The pan assumes the presence of a drain hole from which the hose is removed. This detail eliminates the accumulation of moisture on the surface after washing.
Installation of water supply for a garden shower
The main step in building a garden shower with your own hands is installing a water supply. An excellent reservoir for supplying water is a metal barrel or a plastic tank painted black. Standard volume - from 100 to 200 l. A water level meter or valve should be installed in the tank, which will shut off the flow of water when the tank is full.
The watering can-divider should be installed above head level. This will help to avoid pressure drops during operation.
For a shower tank at the dacha with your own hands, you need to create a greenhouse based on beams covered with PVC film. The tank can be covered with foil, which will help speed up the process of heating the liquid from the sun's rays.
Water tank diagram for a garden shower. The reservoir must be mounted on top of the shower structure. To supply water, you must weld a water pipe or install a pump hose. Heating of water can be done using a heating element - a thermoelectric heater. This method shows itself to be the most practical and economical.
Heating elements are divided into two types - dry and wet. Dry ones operate without direct contact with water, which eliminates the possibility of scale forming on them. Therefore, such devices can last longer. However, wet heating elements are much cheaper and therefore more common. When installing electric heating equipment, it is necessary to take into account safety precautions, ensure that water is isolated from electricity, ground and install.
Insulating the design of a country shower
To insulate a country shower, polystyrene foam, polystyrene foam and other insulating materials are usually used. To insulate the structure you should:
- Fill the frame space with insulating material.
- Cover with plastic wrap and secure with a stapler.
- You can also install overhead insulation on the door.
Soul Project
Drawing. Shower room plan
First of all, it is necessary to complete a project for a summer shower for a summer residence, having decided on the dimensions of the future structure. A container of water raised to a height of 2.5 m will provide a good pressure of the jets. A comfortable cabin will allow the summer resident to wash comfortably in the shower at any time favorable for him. If the shower stall measures 2 X 1.5 m, then inside you can place a clothes hanger, a shelf for soap, gel and shampoos.
The internal space in the stall must have dimensions of at least 100 x 100 cm. The person washing must be able to raise his arms up without any problems and bend down freely without bumping into the walls. The cabin itself must have a shower compartment and a changing room protected from water, at least 60 cm wide. This means that the internal space of the cabin for a summer shower must have dimensions of 160 x 100 cm. However, a design with dimensions of 190 x 140 cm will be more convenient. Add the wall thickness to these parameters, then you will get 200 x 150 cm. In addition, this is an excellent waste-free option for standard sizes boards (see figure above).
Foundation
An outdoor shower does not require a special foundation. When constructing it, it is important to ensure that the frame posts are strictly vertical and ensure that they are firmly connected to the frames and that the supports rest tightly on the pads. These strict requirements are imposed because a heavy tank of water is installed at the top. After the dimensions have been determined, you need to make markings, that is, draw a rectangle on the ground with dimensions of 170 X 110 cm or 190 X 140 cm. A summer country shower can reach a height of 2.5-3 m. With a small support area, it cannot be stable enough. To prevent the structure from toppling over, it is advisable to install a pile or columnar foundation.
Simple to construct, it will reliably hold the shower under wind and other loads: after all, a 200-liter tank has considerable weight. As a material for the foundation, you can use metal pillars, metal or asbestos-cement pipes with a diameter of approximately 90-100 mm and a length of 1.5-2 m. Then four wells 1-1.5 m deep are drilled in the ground in the corners of the shower. Pipes or pillars are inserted into them so that each rises above the ground level by at least 30-50 cm. After that, hewn timber with a section of 100 X 100 mm is laid out at the corners of the foundation from the pillars.
Then the poles are tied with it in the form of a closed strap, starting from the top. This foundation design is called a rigid frame. It is more convenient to assemble the frame on the ground, and then fasten it with long bolts.
The structure will be strong if all the axes coincide, and the fastening is done with long bolts. Then it will be possible to install a water barrel with a volume of about 200 liters on the roof of the shower without any fear.
But the shower stall will be more stable if there are 6 foundation pillars under it. Under the columnar foundation, you need to dig 6 holes measuring 20 X 20 or 30 X 30 cm and a depth of 40-50 cm - it all depends on the structure of the soil. The holes must be filled with cement-sand mortar mixed with pebbles or gravel (see figure).
These will be places for the shower frame. It is more expedient to make its base waterproof, with a slope towards the drain, which is connected to the used water drainage system.
Between the pits, it is necessary to remove the top layer of soil to a depth of 20 cm, and strengthen the formwork from boards or plywood along the edges of the resulting pit. The recess under the shower can be lined with roofing felt or PVC film, but it is better to concrete it, forming a kind of waterproof pan so that the ground under the country shower does not silt. Then fill the bottom of the hole with sand, spill it with water and compact it. Then all this can be filled with mortar so that the platform rises 10 cm above the ground and covers the space for the foundation.
Drawing. Columnar foundation made of stone
From a pan that has a slight slope, water will flow into the gutter. Therefore, a drainage gutter must also have a slope. The drainage of water from the summer shower should be organized into a special drainage ditch (septic tank) on the site or beyond. The water must be drained by a pipe laid in a trench with a certain slope towards the drainage pit.
Under a summer garden shower, you can lay a strip foundation up to 30 cm deep without installing a monolithic concrete platform. To give the building the correct geometric shape, when breaking down the plan on the ground, it is necessary to check the equality of the diagonals of the foundation using a rope or thick fishing line. Then begin digging a trench 30 cm wide and the same depth. The foundation is poured with concrete mortar. It is prepared from 1 part cement, 3 parts clean sand and 5 parts fine crushed stone - 5-20 mm each. Before preparing the solution, the sand is sifted well. The solution is poured into the dug trench. When it has completely hardened, use a level to check the horizontalness of the foundation. If there are any unevenness, they need to be leveled with cement-sand mortar. If you plan to constantly use a shower and heat the water, then you must pour a concrete platform under the foundation or lay it out of brick in the form of a rectangle. The foundation site must be concreted with a slope towards the sewer pipe, and a wooden grate must be placed on top.
You are on a portal about the renovation of apartments and houses, reading an article. You can find on our website a lot of information about design, materials for repairs, remodeling, electrical, plumbing and much more. Use the search bar or sections on the left to do this.
Summer is a great time for a country holiday. It can be overshadowed by the lack of a shower, since a person, regardless of whether he is working or resting, needs to perform water procedures.
If the dacha is used only in the summer, then it is easiest to organize a shower on the site. You can make a mobile shower, or build a solid outbuilding.
Portable summer shower
In stores you can find foot showers. To operate it, you don’t need to build or carry out anything. As a rule, you only need a small container of water to use it.
An existing hose is lowered into the container and connected to the pump. It resembles a small rug. The water comes out through a hose with a watering can, and for it to flow, a person just needs to mark time in one place.
This device is simply irreplaceable, as it is suitable not only for the garden, but also for picnics, and you can take it with you on hikes.
With its help, water procedures can be carried out not only on the street, but also in the house when it is very cool outside.
To do this, you just need to put a basin and wash yourself. Another advantage of a mobile shower is the independent regulation of water temperature. Such a shower at the dacha simply cannot be replaced.
Stationary shower
Many summer residents are interested in how to make a stationary shower. This option is quite expensive compared to the first. However, it will serve you for many years.
Before you start construction, you need to think about where the water will drain from it. It’s good to have an antiseptic on site. You can drain the shower into it.
If it is missing, then you need to make a hole and fill the bottom with expanded clay. A family needs a pit measuring 60x60x60 cm.
If the soil is dominated by sand, the walls of the recess will have to be strengthened so that they do not crumble. A metal mesh or boards that are no longer needed are suitable for this.
Shower base
As a rule, a shower building weighs little. Therefore, there is no point in making a foundation for it; it can be replaced with blocks. They are aligned to the same level so that the structure stands level.
This is much cheaper than a foundation, and takes much less time for construction, since the foundation must dry, and the building can be immediately erected on the blocks.
The blocks should be placed 20 cm from the ground, this is necessary so that the wood does not rot.
If you are going to make a structure from metal, then the blocks do not need to be leveled at a level of 20 cm. Such a frame can be installed on ordinary paving slabs.
Construction
There are two types of construction. The first is when the building is divided into several parts. In one part there is a shower, in the other there is a locker room or technical room where the boiler is installed.
Note!
The second type is a simple shower with a curtain, where only water procedures will be performed. Therefore, the dimensions of the shower are calculated based on what kind of construction is planned.
Types of frame
Metal. The frame can be made of profiled pipe, 3 mm in size. For the work you will need a welding machine.
It is best to weld the pipe joints, this will make the structure stronger. If the device is missing, then the joints can be fastened with special bolts.
Tree. For construction you will need timber. Typically, timber measuring 50x50 mm is used. Before you start construction, you need to make a drawing of the shower in the country.
Shower trim
After the frame has been erected, the shower needs to be covered with material. There are no specific standards for the material. Everyone chooses according to their own pocket.
Let's highlight the most popular materials:
- oilcloth;
- textile;
- wood;
- slate;
- polycarbonate
Water container
You can use absolutely any container as a tank. Basically, these are metal or plastic barrels. They can be purchased at any construction and country stores.
Note!
When choosing, consider your region of residence. For southern cities, any container is suitable, but for northern regions only a metal one, as it heats up faster.
Shower tray
It is best to purchase a ready-made pan, since it will have a drain that will directly drain into the pit. The pallet is made of plastic or metal. Metal will last much longer, so it is advisable to choose it.
Making a summer shower in the country is not so difficult. The main thing is to approach the design thoroughly and calculate in advance the amount of material required.
For clarity, you can look at a photo of a summer shower at the dacha with your own hands. It will make your stay comfortable and enjoyable.
Photo of a shower in the country with your own hands
Note!
Loading...